New 👏 BIKEHAND Bicycle Floor Type Hub Mount Parking Rack Stand – For Mountain And Road Bike Indoor Outdoor Garage Apartment Storage NOT For Disk Brake Bikes ✨

8 reviews for New 👏 BIKEHAND Bicycle Floor Type Hub Mount Parking Rack Stand – For Mountain And Road Bike Indoor Outdoor Garage Apartment Storage NOT For Disk Brake Bikes ✨

1. 

   Rated 4 out of 5

   @rocknrao – April 28, 2018

   Seems to work just fine on a Trek Fx3 with v-brakes. I know there’s a similar model that’s sized for 29er and 700c wheels, but I don’t think that’s the one I ended up with. It works with my 700c quick release rear wheel in either case.The rubber-coated blades just barely reach up into the crevice between the frame and the rear wheel hub, but that seems to be enough to keep the bike standing. If the front wheel, which is unsecured, turns, it makes the bike kind of lean over a bit, but it still manages to stay upright.Lifting the bike up and out of the stand can be awkward, I guess. The stand tends to wobble around and reposition itself on the floor after you lift out. If you’ve got a rear basket on the bike and you’re intending to put cargo in it, you have to wait until after you lift the bike off the stand, or else it’s a bit of a struggle.It’s an elegantly minimal solution that requires no drilling or unscrewing, and doesn’t take up much floor space. I think you could get similar results out of a frame-mounted kickstand at the same cost or less, however, and it would be more portable too. But that would require some wrench work or additional labor cost, whereas the BIKEHAND Rear Hub Stand is entirely ready to go the moment it arrives.

2. 

   Rated 5 out of 5

   The Truth – June 5, 2021

   The only thing I dislike is I didn’t buy it sooner. The plastic rear wheel holder I had before used to tough and throw my derailer out of adjustment so badly I couldn’t ride without taking massive time to readjust the derailer.This products top part exists solely on the left side of the rear axle so it will never mess up your derailer. A stand that touches the right side of your rear axle is now deserving to be extinct. The weighty enough base goes under the rear tire and holds the bike firmly. It won’t tip. It’s a flawless design.This is an excellent bike stand that weighs enough to hold your bike securely just by placing the left end of your rear axle between its two “finger” like protrusions.I have no affiliation with this company, I just think its a great bike stand.

3. 

   Rated 4 out of 5

   Justin – June 7, 2022

   I think this is a great stand for any bike. I’ve been looking for something that has good quality, I’m glad that I settled on this one.

4. 

   Rated 4 out of 5

   Larry M – August 16, 2022

   This was a well piece of metal but I didn’t like to very loose fit on to the axel. it had too much slop for my bike and didn’t fit well on my Dura-Ace wheels but might fit your axel better if it’s thicker.

5. 

   Rated 5 out of 5

   Jordan Wade – October 2, 2022

   Really no explanation needed, it’s a solid peice and holds up very well and adds a bit of color to the room

6. 

   Rated 5 out of 5

   Mel – November 5, 2022

   It’s a great bike stand, very sturdy! My husband loves it for his ride bike.

7. 

   Rated 5 out of 5

   Hector C – November 13, 2022

   We’ll need more details for which bike hub will work better but as now works.?

8. 

   Rated 4 out of 5

   Gilberto Rivera – December 6, 2022

   It just works and it’s impossibly simple. Works on both my road and mountain bikes.